Hallo zusammen,
unser Anschluss wurde heute auf ISDN umgestellt.
- NTBA hängen am Strom und laut Telekommann lief das ISDN Telefon
- Sirrix 4S0 ist in der Starface eingebaut und wird vom System erkannt
- derzeit 1 Kabel von NTBA1 - ISDN1 in Sirrex Port 1 Pin 3 -> 4, 4 -> 3, 5 -> 6, 6 -> 5
getestet:
neue Leitung ISDN extern Mehrgeräteanschluss / Anlagenanschluss
An der Sirrix hinten leuchtet keine LED, in der Starface wird alles grau angezeigt.
/var/log/messages:
Jul 6 20:40:26 starface kernel: r8168: eth0: link down
Jul 6 20:40:26 starface kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
Jul 6 20:40:27 starface kernel: r8168: eth0: link down
Jul 6 20:40:28 starface ntpd[2550]: sendto(188.40.140.97): Invalid argument
Jul 6 20:40:29 starface kernel: sirrix_pfic 00: Setting PCM master to PFIC 0 INTERNAL
Jul 6 20:40:29 starface last message repeated 3 times
Jul 6 20:40:29 starface kernel: r8168: eth0: link up
Jul 6 20:40:29 starface kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Jul 6 20:40:29 starface kernel: r8168: eth0: link up
Jul 6 20:40:30 starface kernel: Zapata Telephony Interface Unloaded
Jul 6 20:40:30 starface kernel: sirrix_dchmon deleted
Jul 6 20:40:30 starface kernel: sirrix_bch deleted
Jul 6 20:40:30 starface kernel: sirrix_pfic Shutting down devices
Jul 6 20:40:30 starface kernel: sirrix_pcm: removed pcm master card type 1, serial 03083eca
Jul 6 20:40:30 starface kernel: sirrix_pfic Disabling interrupts from all IPACs
Jul 6 20:40:30 starface kernel: ACPI: PCI interrupt for device 0000:05:00.0 disabled
Jul 6 20:40:30 starface kernel: sirrix_pfic Device PFIC 00 cleaned up
Jul 6 20:40:30 starface kernel: sirrix_pfic deleted
Jul 6 20:40:30 starface kernel: sirrix_base deleted
Jul 6 20:40:30 starface kernel: sirrix_base Sirrix.PCI release-101216
Jul 6 20:40:30 starface kernel: sirrix_base Initializing Layer 1 Dev
Jul 6 20:40:30 starface kernel: sirrix_base Initializing Layer 1 functions
Jul 6 20:40:30 starface kernel: sirrix_base Initializing Port Management
Jul 6 20:40:30 starface kernel: sirrix_base Initializing Card Management
Jul 6 20:40:30 starface kernel: sirrix_base Initializing datastructure for PCM
Jul 6 20:40:30 starface kernel: sirrix_base initialized
Jul 6 20:40:30 starface kernel: sirrix_pfec Sirrix.PCI release-101216
Jul 6 20:40:30 starface kernel: sirrix_pfec Found 0 devices
Jul 6 20:40:30 starface kernel: sirrix_pfec NOT sorting devices (nosort != 0)
Jul 6 20:40:31 starface kernel: sirrix_pfic Sirrix.PCI release-101216
Jul 6 20:40:31 starface kernel: PCI: Enabling device 0000:05:00.0 (0000 -> 0002)
Jul 6 20:40:31 starface kernel: ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 21 (level, low) -> IRQ 74
Jul 6 20:40:31 starface kernel: sirrix_pfic Card with correct VERSION_ID (0x20061123) found!
Jul 6 20:40:31 starface kernel: sirrix_pfic Card with correct serial number 0x03083eca found!
Jul 6 20:40:31 starface kernel: sirrix_pfic Found 1 devices
Jul 6 20:40:31 starface kernel: sirrix_pfic NOT sorting devices (nosort != 0)
Jul 6 20:40:31 starface kernel: sirrix_pfic Starting up PFIC 00 with serial number 0x03083eca
Jul 6 20:40:31 starface kernel: sirrix_pfic Disabling interrupts from all IPACs
Jul 6 20:40:31 starface kernel: sirrix_pfic Clearing RAM
Jul 6 20:40:31 starface kernel: sirrix_pfic initialized
Jul 6 20:40:31 starface kernel: sirrix_pfiecc Sirrix.PCI release-101216
Jul 6 20:40:31 starface kernel: sirrix_pfiecc Module init
Jul 6 20:40:31 starface kernel: sirrix_pfiecc Looking for devices
Jul 6 20:40:31 starface kernel: sirrix_pfiecc Found 0 devices
Jul 6 20:40:31 starface kernel: sirrix_pfiecc NOT sorting devices (nosort != 0)
Jul 6 20:40:32 starface kernel: sirrix_bch Sirrix.PCI release-101216
Jul 6 20:40:32 starface kernel: sirrix_bch initialized
Jul 6 20:40:32 starface kernel: sirrix_dchmon Sirrix.PCI release-101216
Jul 6 20:40:32 starface kernel: sirrix_dchmon initialized
Jul 6 20:40:32 starface kernel: Zapata Telephony Interface Registered on major 196
Jul 6 20:40:32 starface kernel: Zaptel Version: 1.4.12.1
Jul 6 20:40:32 starface kernel: Zaptel Echo Canceller: MG2
Jul 6 20:40:32 starface kernel: ztdummy: RTC rate is 1024
Jul 6 20:40:32 starface kernel: Registered tone zone 3 (Netherlands)
Jul 6 20:40:33 starface su(pam_unix)[11190]: session opened for user postgres by (uid=0)
Jul 6 20:40:33 starface su(pam_unix)[11190]: session closed for user postgres
Jul 6 20:40:34 starface kernel: usbcore: deregistering driver usb-storage
Jul 6 20:40:34 starface kernel: Initializing USB Mass Storage driver...
Jul 6 20:40:34 starface kernel: usbcore: registered new driver usb-storage
Jul 6 20:40:34 starface kernel: USB Mass Storage support registered.
Jul 6 20:40:34 starface LCDd: pyramid: open(/dev/ttyUSB0) failed: No such file or directory
Jul 6 20:40:34 starface LCDd: Driver [pyramid] init failed, return code < 0
Jul 6 20:40:34 starface LCDd: Could not load driver pyramid
Jul 6 20:40:34 starface LCDd: There is no output driver
Jul 6 20:40:34 starface LCDd: Critical error while initializing, abort.
Jul 6 20:40:38 starface su(pam_unix)[11559]: session opened for user daemon by (uid=0)
Jul 6 20:40:38 starface su(pam_unix)[11559]: session closed for user daemon
Jul 6 20:41:00 starface kernel: sirrix_pfic 00: Setting PCM master to PFIC 0 INTERNAL
Jul 6 20:41:00 starface last message repeated 3 times
Jul 6 20:41:00 starface kernel: sirrix_base setting initial pcm sync and master
Jul 6 20:41:00 starface kernel: sirrix_pcm: trying to set card type 1, serial 03083eca as master without force
Jul 6 20:41:00 starface kernel: sirrix_pcm: trying to set new pcm master card type 1, serial 03083eca
Jul 6 20:41:00 starface kernel: sirrix_pcm: done setting pcm master to card type 1, serial 03083eca
Jul 6 20:41:00 starface kernel: sirrix_pcm: current pcm master is card type 1, serial 03083eca
Jul 6 20:41:00 starface kernel: sirrix_pcm: trying to set sync to card type 1, serial 03083eca
Jul 6 20:41:00 starface kernel: sirrix_pcm: done setting sync to card type 1, serial 03083eca
Jul 6 20:41:01 starface kernel: sirrix_pfic 0000: enabling interrupts
Jul 6 20:41:01 starface kernel: sirrix_pfic 0001: enabling interrupts
Jul 6 20:41:01 starface kernel: sirrix_pfic 0002: enabling interrupts
Jul 6 20:41:01 starface kernel: sirrix_pfic 0003: enabling interrupts
Jul 6 20:41:06 starface sshd(pam_unix)[11708]: session opened for user root by (uid=0)
Jul 6 20:41:11 starface LCDd: pyramid: open(/dev/ttyUSB0) failed: No such file or directory
Jul 6 20:41:11 starface LCDd: Driver [pyramid] init failed, return code < 0
Jul 6 20:41:11 starface LCDd: Could not load driver pyramid
Jul 6 20:41:11 starface LCDd: There is no output driver
Jul 6 20:41:11 starface LCDd: Critical error while initializing, abort.
srx show layers:
starface*CLI> srx show layers
SYNC: internal
l1=0x840d8f0: port=0x0000 type=BRI mode=TE ptp=0 syncAllowed=1 guards=0 act=0 st=ST_L1_IPAC_F4_PENDING_ACTIVATION starting=0 restarting=0 started=1
l2h=0x8436ac0
l2=0x8179388: tei= -1, uiq=0, iq=0, siq=0, st='ST_L2_1_TEI_UNASSIGNED':
l3h=0x8196678: cr_out={ }, cr_in={ }, oq=0, iq=0
l1=0x842cdc8: port=0x0001 type=BRI mode=TE ptp=0 syncAllowed=1 guards=0 act=0 st=ST_L1_IPAC_F4_PENDING_ACTIVATION starting=0 restarting=0 started=1
l2h=0x8433170
l2=0x84168c0: tei= -1, uiq=0, iq=0, siq=0, st='ST_L2_1_TEI_UNASSIGNED':
l3h=0x84312c0: cr_out={ }, cr_in={ }, oq=0, iq=0
l1=0x842cdf8: port=0x0002 type=BRI mode=TE ptp=0 syncAllowed=1 guards=0 act=0 st=ST_L1_IPAC_F4_PENDING_ACTIVATION starting=0 restarting=0 started=1
l2h=0x8434e18
l2=0x819d208: tei= -1, uiq=0, iq=0, siq=0, st='ST_L2_1_TEI_UNASSIGNED':
l3h=0x8430c40: cr_out={ }, cr_in={ }, oq=0, iq=0
l1=0x842ce38: port=0x0003 type=BRI mode=TE ptp=0 syncAllowed=1 guards=0 act=0 st=ST_L1_IPAC_F4_PENDING_ACTIVATION starting=0 restarting=0 started=1
l2h=0x8419d70
l2=0x842ec78: tei= -1, uiq=0, iq=0, siq=0, st='ST_L2_1_TEI_UNASSIGNED':
l3h=0x819d670: cr_out={ }, cr_in={ }, oq=0, iq=0
Wie bekomme ich die Anschlüsse zum Laufen? Habe ich irgendetwas übersehen?